This is the Team Associated RC8e 1/8 Scale 4WD Electric Buggy Combo
Pack. This package includes the Associated RC8e buggy, an LRP SPX8
Electronic Speed Control and an LRP Vector 8 2,800kV Brushless Motor!
RC8e: The RC8e engineering team has developed a practical
design that incorporates the same exceptional strength, durability,
cornering capability, jumping ability, and rough track handling that the
nitro powered RC8 is notorious for. With special features such as a
hard anodized machined chassis, correctly balanced and optimized weight
distribution, composite “Big Bore” shocks featuring 4mm gold shafts,
upgraded steering system, and exclusive body design, every inch of the
RC8e screams high performance and durability. In fact, the RC8e has
proved itself as a top competitor with a First Place finish in its debut
event!
SPX8: The SPX8 Competition Brushless Speed Control is based on
one of the most successful competition speed controls ever—the SPHERE
Competition TC Spec. Only the best of the best in today’s brushless
racing was good enough to use as a base for the development of the LRP
1/8 Brushless System. These successful genes can now be found in the
SPX8 Competition Brushless ESC. It aims to reach the peak of 1/8
brushless speed controls with its high tech features. For this reason
the TC Spec has been adapted to the specific demands of 1/8 racing. It
now features special 1/8 software and has been specially optimized for
use with 2S and 4S LiPo batteries. The result is a high end speed
control that will excite the 1/8 electric RC car scene.
VECTOR 8: The VECTOR 8 Brushless Modified is based on the IFMAR
World Championship winning X12 brushless modified technology. In the
past months, X12 based motors set benchmarks when it came to outstanding
performance and ultimate reliability at top level races around the
world. Now 1/8 drivers can benefit from this technology advantage as
well. The Vector 8 Brushless Modified is specifically tailored for 1/8
off road racing with its longer tear down with special cooling fins,
longer stack, magnet, and shaft for higher torque and maximum
performance. Includes high performance fan for maximum cooling and
unique mounting hardware for perfect installation into all RC
cars—simply plug into the receiver!
RC8e Buggy Features:
- Molded battery tray supports two ROAR approved 1/10 scale size 7.4v LiPo battery packs with room for foam pads
- Receiver box, servo, and battery tray are removable in one piece for easy maintenance and cleaning
- Convenient wire routing keeps critical electronic wires out of drive train components and simplifies dis-assembly
- Includes pinion gear (15T) and molded composite spur gear (46T)
- Rigid one piece motor mount utilizes standard motor screw mounting pattern
- Large elevated speed control mounting area allows for easy screw mounting of common speed controllers
- Upgraded dual bell crank steering for more consistent steering and reduced bump steer
- 16mm Big Bore molded composite shocks with pre-load clips
- Hard anodized 7075 T6 aluminum chassis
- 3mm aluminum shock towers
- Durable 10mm thick suspension arms
- Rear molded CVA boots to keep dirt and mud out of rear joints
- Alloy steel turnbuckles
- Caster blocks adjust 14, 16, or 18 degrees with molded inserts
- Adjustable suspension pivot bushings for different pivot height options
- 4.30:1 ratio gearboxes
- 3.5mm light CVA drive train
- Pre-drilled wing with adjustable angle and location
- Blue aluminum drive hexes
- Blue aluminum nylock wheel nuts
- 83mm Factory Team wheels (ASC89296)
- Speed control mounting area includes convenient switch mounting boss
- Utilizes 3 hook and loop straps to secure LiPo batteries into battery tray
- Enclosed receiver box to protects electronic components
- Unpainted RC8e body with cooling scoops (ASC89523)
SPX8 ESC Features:
- Revolutionary small size for 1/8 scale models
- Special 1/8 Power Profiles
- Optimized for 2S - 4S LiPo battery operation
- Internal Temp Check System 2
- Low profile heat sink with integrated high performance fan
- Fully adjustable drive modes with different adjustment possibilities
- Sensored design
Vector 8 Features
- 13mm Magnet: New sintered 13mm magnet size and grade, for best efficiency and midrange torque. 5mm high-strength output shaft with oversized bearings for the toughest demands in 1/8 racing.
- PreciSensor TM System: Revolutionary precise sensor positioning for best power, throttle feel and efficiency. Fully adjustable and replaceable
- Re-buildable: Machined 7075 T6 aluminum can
- Universal Fit:
Fits all common 1/8 Off Road
Brushless models.
- IFMAR World Champion Technology: XTEC X12 World Champion Technology now available for 1/8 brushless cars
- Air Flow And Cooling Optimized Teardown: Flow optimized cut-outs for highest performance even on long runs. Including fan and holder
- Special 1/8 winding style: Special 1/8 Off Road power windings developed and tested by the LRP Factory Team
RC8e SPECS:
Type: Electric Off Road Buggy
Scale: 1/8
Length: 18.5 in (470mm)
Width: 12.0 in (305mm)
Wheelbase: 12.7 in (323mm)
Weight: 7.70 lb (3492g); approximate, will vary depending upon
electronics used
Drivetrain: 4WD
Kit/RTR: Kit
SPX8 ESC Specifications:
Forward: Yes
Reverse: Yes
Brake: Yes
Input Voltage: 7.2 - 14.8V (2S - 4S LiPo)
Motor Limit: none
Dimensions (WxLxH): 37.6x33.1x32.5mm
Weight: 45g
BEC Voltage: 6V
Vector 8 Specifications:
RPM per volt: 2800kv
Power
(at 14.8V): 1360W
Weight: 275g
Diameter:
41mm
Length: 66mm
Output Shaft:
5mm
Needed To Complete:
- R/C 2 channel surface frequency radio system
- High torque steering servo
- Batteries: (1) 4S, or (2) 2S Hardcase LiPo battery packs (7.4v or 14.8v)
- LiPo Battery charger
- Tire glue
- Paint for Lexan body
- Tools: Phillips screwdriver, needle nose pliers, pencil type soldering iron with Rosin core solder to solder motor wires, thread locking compound, hobby knife, precision ruler, body scissors.
This product was added to our catalog on March 17, 2010