RaceTek CL-0615-19 TinyFPV "Stage 3" Motor Set (19,600kV)
RTK2511
This item is discontinued and no longer available for purchase. You may want to search our site for a similar item.
The CL-0615-19 TinyFPV Stage 3 Motor Set is the top of the line in turning your Blade Inductrix or Eachine E010 micro FPV quadcopter into the ultimate racer! These 19,600kV motors will add insane amounts of power to your mini quad enabling the fastest climb outs and tightest turns. Package includes two 19,600kV clockwise motors and two 19,600kV counter clockwise motors with factory installed 1.25mm connectors.
NOTE:
- Red/Blue wire motors with green bell are CW, and when looking from the top should be installed in the right front/left rear positions.
- Black/White wire motors with black bell are CCW, and when looking from the top should be installed in the left front/right rear positions.
Specifications:
- Speed: 19,600Kv
- Operating Voltage: 1.5-3.7V
- Load Current at 3.7V: 2.0A
- Dimensions:
- Diameter: 6mm
- Length: 15mm
- Shaft Diameter: 0.8mm
- Shaft Length: 5mm
- Weight: 1.8g
- Wire Length: 50mm
- Connector: Micro-JST-1.25
This product was added to our catalog on March 20, 2017
Anonymous
Verified Owner
Friday, Apr 7 2017 (about 7 years ago)
RaceTek CL-0615-19 TinyFPV "Stage 3" Motor Set (19,600kV)
These motors are very fast. They also draw a lot of current. I use Lynx "special sauce"(17500KV) motors on my lightened/modded Inductrix FPV. It flies very well with them. Weight is 20.5 grams without the battery and 26.25 grams with a Tattu 220mah battery in it giving 3:30 flight times. With these "Stage 3" motors, it went down to less than two minutes but the power is impressive. Punch out feels like you have brushless motors in it. Bumping the ceiling now becomes a problem. I use Eachine props with two blades cut off. I also noticed that the drone now had a bit of a wobble. I tried a few tricks to cure it but nothing worked. It cleared up when I went back to the slower motors(I'm guessing these draw so much current that the gyros are not receiving the power required, but that is purely a guess). I bought a spare frame and just leave these motors mounted with Rakon 3-bladed props in it and switch over the rest of the electronics when I want 90 seconds of "The world's fastest Inductrix FPV". Judging by my overtaking speed of my friends Inductrix FPV, I would say that it is twice as fast as stock. I hope the battery technology catches up soon and they make a 500mah battery that will fit. Verdict. If crazy speed at the expense of flight time is your thing, these are for you. I will rate them as "good" because they do what they are supposed to do, give you more power. They did not say that flight time wouldn't be affected.
Update 5-21-2017
The wobble I attributed to high motor draw was actually a defective board. I damaged the original board and replaced it with another stock board and when I tried these motors with the new set-up, it flew perfectly. I further reduced the weight to 19.20 grams(without battery) and it now flies for 3:00 without a problem. These motors make it an outdoor quad as it can now handle up to 7 mph of wind whereas before, if the leaves were moving at all, I flew indoors.
Update 5-21-2017
The wobble I attributed to high motor draw was actually a defective board. I damaged the original board and replaced it with another stock board and when I tried these motors with the new set-up, it flew perfectly. I further reduced the weight to 19.20 grams(without battery) and it now flies for 3:00 without a problem. These motors make it an outdoor quad as it can now handle up to 7 mph of wind whereas before, if the leaves were moving at all, I flew indoors.
Henry Chou
Verified Owner
Tuesday, Dec 12 2017 (about 6 years ago)
RaceTek CL-0615-19 TinyFPV "Stage 3" Motor Set (19,600kV)
Great motors for a great value for my tiny whoop! These have decent power and allow me to do to tricks without dropping altitude.