Scorpion HK-4225-550 Limited Edition Brushless Motor w/6mm Shaft (5770W, 550kV)
SCP-HK2-4225-550
This item is discontinued and no longer available for purchase. You may want to search our site for a similar item.
This is the Scorpion HK-4225-550 Limited Edition Brushless Motor. The HKII-4225-550 Limited Edition motor was developed for 600 class helicopters that use 12S Li-Po power. This motor represents the most technologically advanced power source ever offered for a 600 class electric helicopter. Each HKII-4225 Limited Edition motor is wound with a single strand of 1.35mm wire for the highest possible efficiency. The HKII-4225-550 is capable of running continuously at an input power of 3550 watts at 80 amps, and can handle peak inputs of 5770 watts and 130 amps!
Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Plated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.
Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.
NOTE: *This motor is using 30mm bolt spacing for mounting, with M4 screw holes. Also, gold connectors are not included.
Specifications:
Stator Diameter: 42mm (1.65 in)
Stator Thickness: 25mm (0.98 in)
No. of Stator Arms: 12
No. of Stator Poles: 10
Motor Wind: 10 Turn Delta
Motor Wire: 1-Strand 1.35mm
Motor Kv: 550KV RPM/Volt
No-Load Current (Io/10V): 1.77 Amps
Motor Resistance (RM): 0.016 Ohms
Max Continuous Current: 80 Amps
Max Continuous Power: 3550 Watts
Weight: 393 Grams (13.77 oz)
Outside Diameter: 52.3mm (2.06 in)
Shaft Diameter: 5.98mm (0.24 in)
Body Length: 51.50mm (2.03 in)
Overall Shaft Length: 91.5mm (3.60 in)
Max Lipo Cell: 12s
Max Peak Current: 130 Amps (5 seconds)
Max Peak Power: 5770 Watts (5 seconds)
Motor Timing: 5deg
Drive Frequency: 8kHz
Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Plated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.
Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.
NOTE: *This motor is using 30mm bolt spacing for mounting, with M4 screw holes. Also, gold connectors are not included.
Specifications:
Stator Diameter: 42mm (1.65 in)
Stator Thickness: 25mm (0.98 in)
No. of Stator Arms: 12
No. of Stator Poles: 10
Motor Wind: 10 Turn Delta
Motor Wire: 1-Strand 1.35mm
Motor Kv: 550KV RPM/Volt
No-Load Current (Io/10V): 1.77 Amps
Motor Resistance (RM): 0.016 Ohms
Max Continuous Current: 80 Amps
Max Continuous Power: 3550 Watts
Weight: 393 Grams (13.77 oz)
Outside Diameter: 52.3mm (2.06 in)
Shaft Diameter: 5.98mm (0.24 in)
Body Length: 51.50mm (2.03 in)
Overall Shaft Length: 91.5mm (3.60 in)
Max Lipo Cell: 12s
Max Peak Current: 130 Amps (5 seconds)
Max Peak Power: 5770 Watts (5 seconds)
Motor Timing: 5deg
Drive Frequency: 8kHz
This product was added to our catalog on October 5, 2012