RC OMG H4-ST-BF20S "High Torque" Brushless Aluminum Case Metal Gear Servo (High Voltage)
OMGSBS002
This item is discontinued and no longer available for purchase. You may want to search our site for a similar item.
This is the RC OMG H4-ST-BF20S "High Torque" Brushless All Aluminum Case Metal Gear Servo. The RC OMG H4 Series Servos are powerful and precise, and deliver incredible speed and torque. A full aluminum case, combined with long wear 7075 Aluminum anodize titanium, or 304 stainless steel gear trains, high voltage electronics and precision brushless motors deliver quality that will soon become legendary.
Features:
- Super high 12 bit (4096) resolution
- Robust output for superb response in extreme maneuvers
- Zero dead band assures legendary precision
- Aluminum middle case helps dissipate heat
- Digital precision provides great accuracy and performance
- Ball bearing-supported 25T output shaft
- Compatible with all Radio systems
- Pulse width travel is adjustable
- Recommended for 1/8 buggies drift cars and 700 class helicopter cyclic
Specifications:
- Type: Digital
- Operating Voltage Range: 4.8-7.4V DC
- Bushing or Bearing: Bearing
- Bearing Type: Dual Ball Bearings
- Speed s/60°:
- @6.0V: 0.08
- @7.4V: 0.07
- @8.4V: 0.065
- Torque:
- @6.0V: 250 oz./in. (18 kg./cm.)
- @7.4V: 278 oz./in. (20 kg./cm.)
- @8.4V: 305 oz./in. (22 kg./cm.)
- Size: 1.57x0.79x1.50" (40x20x38mm)
- Weight: 2.53 oz (72g)
- Motor Type: Brushless
- Control System: +Pulse Width Control 1500µsec Neutral
- Required Pulse: 3-5 Volt Peak to Peak Square Wave
- Operating Temperature Range: 14° - 122° F (-10° - 50° C)
- Idle Current (@6.0V/7.4V/8.4V): 5mA/5mA/5mA
- No Load Running Current (6.0V/7.4V/8.4V): 180mA/220mA/250mA
- Stall Current (6.0V/7.4V/8.4V): 3800mA/4900mA/5400mA
- Dead Band Width: 2µs
- Potentiometer Type: Rotating (Max.220°)
- Connector Wire Length: 11.8 in. / 300 mm. OMG wire
- Connector Wire Gauge: 22 AWG
- Connector Type: JR
- Gear Type: Stainless Steel
- Frequency: 330Hz
- Shaft: 5.85mm 25T
NOTE: Maximum 7.4V Operating Voltage is recommended for the servo, because higher voltage and current will cause fatal damage to the servo motor.
This product was added to our catalog on September 27, 2016
Jason B
Verified Owner
Sunday, Dec 21 2014 (about 9 years ago)
RC OMG H4-ST-BF20S "High Torque" Brushless Aluminum Case Metal Gear Servo (High Voltage)
Very high quality servo. Geartrain is extremely smooth and silent. No digital noise or chatter like I'm used to seeing with my other digital servos. Running in an SCT with no servo saver, has taken many hard hits some even popping off the steering linkages and still works and sounds like new.
Keith Laymon
Verified Owner
Thursday, Jan 7 2016 (about 8 years ago)
RC OMG H4-ST-BF20S "High Torque" Brushless Aluminum Case Metal Gear Servo (High Voltage)
This servo is super fast with tons of torque and it's SILENT. None of the chatter/buzzing while holding center like every other servo I've used. When it was powered up and holding center and I was torquing down the servo horn, it never made a peep. I'm running mine at 7.4V which gives a nice increase to speed and torque. This thing has plenty of both. Installed on an RC8B3e with a Tekin RX8 ESC with no additional caps or external BEC.