Align 3S1P LiPo Battery 30C (11.1V/850mAh)
AGNHBP85001
This item is discontinued and no longer available for purchase. You may want to search our site for a similar item.
This is an Align 3S1P, 30C, 11.1V, 850mAh Li-Polymer Battery. This Li-poly battery features high efficiency and high discharge capabilities, making this pack suitable for the TREX 250 series as well as model airplanes, and any other application that could benefit from a 30C 3S pack with these specifications.
Specifications:
Type: Lithium Polymer
Capacity: 850mAh
Voltage: 11.1V nominal
Number of Cells: 3
Weight: 70 grams (Not including connectors)
Configuration: 3S1P
Dimensions: 55x30x24.5mm
Maximum Continuous Discharge: 30C
Maximum Burst Discharge: 40C
IMPORTANT:
1) You will need a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)
2) You must not over discharge the Li-Poly battery pack.
3) Read the instructions carefully before operating this battery.
NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.
Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
Specifications:
Type: Lithium Polymer
Capacity: 850mAh
Voltage: 11.1V nominal
Number of Cells: 3
Weight: 70 grams (Not including connectors)
Configuration: 3S1P
Dimensions: 55x30x24.5mm
Maximum Continuous Discharge: 30C
Maximum Burst Discharge: 40C
IMPORTANT:
1) You will need a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)
2) You must not over discharge the Li-Poly battery pack.
3) Read the instructions carefully before operating this battery.
NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.
Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on November 13, 2009
Michael Griffin
Verified Owner
Saturday, Aug 9 2014 (about 9 years ago)
Align 3S1P LiPo Battery 30C (11.1V/850mAh)
I have used these many times before. These are a perfect fit for the T-Rex 250. I just purchased and received a new one of these, and to my surprise, they are rated for 5C charge rate! 5C!
It takes one hour to charge my old 1C packs from storage to full. It only takes fifteen minutes to charge my new pack at 4C! Sweet!
It takes one hour to charge my old 1C packs from storage to full. It only takes fifteen minutes to charge my new pack at 4C! Sweet!