|
This is the Hyperion EOS 0720i NET3 7S 16N Charger, with Integrated LBA10A balancer, TCS and 250W charger power. The EOS 0720i NET3 is an extremely powerful (250W, 20A), versatile, easy-to-use charger with special features for speed charging lithium packs up to 7S! Even 2C rates are possible with large 7S packs. The integrated LBA10+ balancer has 300mA balance power per cell. Terminal Capacity Selection, PS Load Control, PC Dataport, and User-Upgradable firmware round out this great package. But the features don't stop there. Two of these chargers can be Networked to allow charging two similar packs as a single unit, up to 14S total at 500W charge power. Nothing else on the planet offers so much power at such a low cost. Charger includes: Output Charge Cord/Connector set and Hyperion Balance Multi-Adapter for 2S to 7S and a USB data cable
Specifications & Features:
- 12-bit Resolution for max accuracy
- 250W max CHARGE Output
- 0.1A to 20.0A max Charge Current in 0.1A steps (constrained by 250W max with 14.5V+ DC Input)
- 80W/10A max DISCHARGE limits
- STORE MODE allows fast and simple discharge to ~60% capacity for proper storage of Lithium Battery types = longer battery life.
- Charges/Discharges 1 to 7 cells Lithium Polymer Batteries Per Port (3.7V/cell nominal types)
- Charges/Discharges 1 to 7 cells Lithium Ion Batteries Per Port (3.6V/cell nominal types)
- Charges/Discharges 1 to 7 LiFePO4 (A123) cells (LiFePO4 3.3V/cell nominal, A123 3.3v support)
- Charges/Discharges/Cycles 1-16 cell NiCd/Ni-MH in three modes: Normal, Linear, and Automatic
- Charges/Discharges 1~12 cell Lead Acid Batteries (Pb, 2V/cell)
- Allows Lithium-Type batteries to 50,000mAh and PB (lead/acid) batteries to 100Ah capacity
- Built-in Hyperion LBA10 Balancer with 300mA max balance rate/cell and new 12-Bit measurement resolution
- TCS - Terminal Capacity Selection
- Rich Data Displays during and after charging and balancing
- USB PC Port for Data Logging, Firmware upgrades, and future Charger Control Software System (Nov1~Dec1 2009)
- Temperature Sensor Ports & Temp Stop settings*
- Wide Voltage Input Range 11v~28v for higher efficiency when charging high-voltage packs, and compatibility with a wider selection of AC/DC power supplies
- Power Supply Amperage Control to allow reliable charging with lower-output power supplies
- Power Supply Voltage Control (PS Load Control) works in concert with Amperage control to insure the charger does not overload your power supply
- Input Cable with 4mm Male Connectors + Clamps
- Output Cable Set Included, with 4mm Connectors
- Integral, Thermostat-Controlled Cooling Fans
- Rugged Aluminum Case with Insulating End Caps
- 2-Line, 16-Character, Yellow Backlit LCD Data Display. Highly visible in all conditions
- 20 User-definable Memory Positions
- Firmware upgradable via Win PC**. USB Cable included.
NOTE: EOS0720iNET3 is designed to charge single Lithium-based packs up to 7S max, you CANNOT charge a single "unit" pack greater than 7S using one or both DUO ports no matter the wiring. For flight packs larger than 7S, Network two NET3 in SYNC MODE to balance charge two separate packs, which after charge are series-wired to make the flight pack. (so 2x2S=4S up to 2x7S=14S series flight packs are possible)
* Temp sensors available separate: #HP-EOSTMPSEN or EOS1210i-SEN
** Firmware upgrades only available if/when improvements are identified in future.
The manual for this charger can be downloaded here. Software updates and pc link software is available here
|
