Hitec D954SW High Torque Steel Gear Servo (High Voltage)

Read Reviews
Write a Review
Hitec D954SW High Torque Steel Gear Servo (High Voltage)
Back Order Now
You may back order this item and it will ship when it arrives.
Price: $89.99

Please Log in to receive a notification when this item arrives in stock.

Save In List
This item earns up to 90 VIP Reward Points Learn More
The Hitec D954SW High Torque Steel Gear Servo, a technologically-advanced servo that is powered by Hitec's 32-bit MCU (Microcontroller Unit) and 12-bit ADC (Analog to Digital Converter) industrial science and possess Smart Sense engineering with rapid, high resolution response. The servos unprecedented programmability and wide-voltage capabilities deliver the most progressive, leading-edge performance for all your radio control needs. Built with incredibly durable steel gears, the D930SW are the perfect upgrade from Hitec's popular HS-7954SH servo.

Features:
  • Programmable PWM Digital Amplifier
  • 32-Bit MCU with 12-Bit ADC Circuitry
  • 4096 Resolution
  • 1M Cycle Long Life Potentiometer
  • Wide Operating Voltage (4.8 ~ 8.4 Volts DC)
  • Dual Ball Bearing Supported Output Shaft
  • 25-Tooth Output Spline
  • Coreless Metal Brush Motors
  • Nylon Reinforced Plastic Upper and Lower Case
  • Diamond Cut Aluminum Heat Sink Center Case
  • Dust Resistant and Splash Proof Case
  • Programmable Features:
  • End Point Adjustments
  • Direction
  • Fail Safe
  • Dead Band
  • Speed (Slower)
  • Soft Start Rate
  • Overload Protection
  • Data Save / Load
  • Program Reset
Specifications:
Operating Voltage Range (Volts DC): 4.8V ~ 7.4V
Speed (Second @ 60°): 0.19 ~ 0.12
Maximum Torque Range oz./in.: 251 ~ 405
Maximum Torque Range kg./cm.: 18.0 ~ 29.0
Current Draw at Idle: 30 mA
No Load Operating Current Draw: 500 mA
Stall Current Draw: 5,200 mA
Dead Band Width: 1 µs
Dimensions (Inches): 1.57 x 0.78 x 1.46
Dimensions (Metric): 40.0 x 20.0 x 37.0
Weight (Ounces): 2.40
Weight (Gram): 68.0
Circuit Type: 32bit Programable Digital
Motor Type: Coreless Metal Brush
Gear Material: MK 1st Gear & 3 Steel Alloy Gears
Bearing Type: Dual Ball Bearing
Output Shaft (type/Ømm): H25T
Case Material: Plastic/Aluminum
Dust/Water Resistance: Splash Proof
Connector Gauge (AWG)/Strand Count: 20/80

Includes:
  • (1) D954SW High Torque Steel Gear Servo
  • (3) Steel Alloy Gears Set
  • Metal / Karbonite 1st Gear Set
  • Plastic/Aluminum Case Set
  • Applicable Horns & Screws
Limited Warranty:
Hitec Servo Warranty: Each Hitec servo is backed by a limited two-year warranty from the date of purchase. Hitec RCD USA, INC. shall REPAIR OR REPLACE, at Hitec RCD, INC., defective equipment covered by this warranty, otherwise the purchaser and/or consumer is responsible for any charges for the repair or replacement of the product.

This product was added to our catalog on December 18, 2019

Matt Lee
Wednesday, Jan 19 2022 (about 2 years ago)
Hitec D954SW High Torque Steel Gear Servo (High Voltage)
Worked well for 1-1/2 years through several pretty severe tumbles on my Axial Capra. Broke a tooth on a very minor tumble, and 10 mins later the whole thing was stripped. Called Hitec, gears aren't covered under their two-year warranty, and that's not mentioned in the section for servo warranty, it's covered later under the general limitations of the warranty, which I didn't read until after I was badgering them about the warranty. However, they honored the first paragraph after I was a squeaky wheel by sending me a new gear set.

All that said, it's not quite perfect, but it's quite good, and after all is said and done, I'd buy another.